{"id":2362,"date":"2018-10-25T18:59:03","date_gmt":"2018-10-25T10:59:03","guid":{"rendered":"http:\/\/www.51cos.com\/?p=2362"},"modified":"2018-10-27T14:26:31","modified_gmt":"2018-10-27T06:26:31","slug":"mt7628anmt7612en%e4%b8%8d%e7%9f%a5%e5%90%8d%e8%b7%af%e7%94%b1%e5%99%a8%e7%83%a7%e5%bd%95openwrt%e8%bf%87%e7%a8%8b","status":"publish","type":"post","link":"http:\/\/www.51cos.com\/?p=2362","title":{"rendered":"MT7628AN+MT7612EN+64MB DDR+8M SNOR\u8def\u7531\u5668PCB\u70e7\u5f55UBOOT\/PandoraBox\/OpenWRT\u8fc7\u7a0b"},"content":{"rendered":"
OpenWRT\u6700\u65b0\u5de5\u7a0b\u76ee\u5f55\uff1ahttp:\/\/downloads.openwrt.org\/releases\/18.06.0\/targets<\/div>\n

\u62ff\u5230\u4e00\u4e2a\u4e0d\u77e5\u9053\u7684\u5f00\u53d1\u677f\uff0c\u914d\u7f6e\u5982\u4e0b\uff1a<\/p>\n

CPU\uff1aMT7628AN
\n5G WiFi\uff1aMT7612EN
\nDDR\uff1aWinbond W9751G6K8-251 \uff0864MB\uff09
\nSNOR\uff1a25Q64FVSIG \uff088MB\uff09 <\/p>\n

\u91cc\u9762\u7684\u56fa\u4ef6\u53ef\u4ee5\u5f00\u673a\uff0c\u4e32\u53e3\u6253\u5370\u4fe1\u606f\u5982\u4e0b\uff1a<\/p>\n

Restarting system.
\n[04030C0D][04030C0E]
\nDDR Calibration DQS reg = 00008888<\/p>\n

U-Boot 1.1.3 (Oct 16 2016 – 19:48:39)<\/p>\n

Board: Ralink APSoC DRAM: 64 MB
\nrelocate_code Pointer at: 83fb4000
\n******************************
\nSoftware System Reset Occurred
\n******************************
\nflash manufacture id: c8, device id 40 17
\nfind flash: GD25Q64B
\n*** Warning – bad CRC, using default environment<\/p>\n

============================================
\nRalink UBoot Version: 5.0.0.0
\n——————————————–
\nASIC 7628_MP (Port5<->None)
\nDRAM component: 512 Mbits DDR, width 16
\nDRAM bus: 16 bit
\nTotal memory: 64 MBytes
\nFlash component: SPI Flash
\nDate:Oct 16 2016 Time:19:48:39
\n============================================
\nicache: sets:512, ways:4, linesz:32 ,total:65536
\ndcache: sets:256, ways:4, linesz:32 ,total:32768 <\/p>\n

##### The CPU freq = 580 MHZ ####
\n estimate memory size =64 Mbytes
\nRESET MT7628 PHY!!!!!!
\nPlease choose the operation:
\n 1: Load system code to SDRAM via TFTP.
\n 2: Load system code then write to Flash via TFTP.
\n 3: Boot system code via Flash (default).
\n 4: Entr boot command line interface.
\n 9: Load Boot Loader code then write to Flash via TFTP.
\ndefault: 3
\n 0 <\/p>\n

3: System Boot system code via Flash.
\n## Booting image at bc050000 …
\n Image Name: Linux Kernel Image
\n Image Type: MIPS Linux Kernel Image (lzma compressed)
\n Data Size: 3783625 Bytes = 3.6 MB
\n Load Address: 80000000
\n Entry Point: 8000c150
\n Verifying Checksum … OK
\n Uncompressing Kernel Image … OK
\nNo initrd
\n## Transferring control to Linux (at address 8000c150) …
\n## Giving linux memsize in MB, 64<\/p>\n

Starting kernel …<\/p>\n

LINUX started…<\/p>\n

THIS IS ASIC
\nLinux version 2.6.36 (ziqiang@ziqiang) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #21 Wed Jun 13 22:27:45 CST 2018<\/p>\n

The CPU feqenuce set to 575 MHz<\/p>\n

MIPS CPU sleep mode enabled.
\nCPU revision is: 00019655 (MIPS 24Kc)
\nSoftware DMA cache coherency
\nDetermined physical RAM map:
\n memory: 04000000 @ 00000000 (usable)
\nInitrd not found or empty – disabling initrd
\nZone PFN ranges:
\n Normal 0x00000000 -> 0x00004000
\nMovable zone start PFN for each node
\nearly_node_map[1] active PFN ranges
\n 0: 0x00000000 -> 0x00004000
\nBuilt 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
\nKernel command line: console=ttyS1,57600n8 root=\/dev\/ram0 console=
\nPID hash table entries: 256 (order: -2, 1024 bytes)
\nDentry cache hash table entries: 8192 (order: 3, 32768 bytes)
\nInode-cache hash table entries: 4096 (order: 2, 16384 bytes)
\nPrimary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
\nPrimary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
\nWriting ErrCtl register=0003dd70
\nReadback ErrCtl register=0003dd70
\nMemory: 58172k\/65536k available (3253k kernel code, 7308k reserved, 778k data, 2480k init, 0k highmem)
\nNR_IRQS:128
\nconsole [ttyS1] enabled
\nCalibrating delay loop… 386.04 BogoMIPS (lpj=772096)
\npid_max: default: 32768 minimum: 301
\nMount-cache hash table entries: 512
\nNET: Registered protocol family 16
\nRALINK_GPIOMODE = 54050404
\nRALINK_GPIOMODE = 54040404
\n***** Xtal 40MHz *****
\nstart PCIe register access
\nRALINK_RSTCTRL = 2400000
\nRALINK_CLKCFG1 = fdbfffc0<\/p>\n

*************** MT7628 PCIe RC mode *************
\nPCIE0 enabled
\nPort 0 N_FTS = 1b105000
\ninit_rt2880pci done
\nbio: create slab <bio-0> at 0
\nvgaarb: loaded
\npci 0000:00:00.0: BAR 0: can’t assign mem (size 0x80000000)
\npci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
\npci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
\npci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
\npci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
\npci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
\npci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
\npci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
\npci 0000:00:00.0: PCI bridge to [bus 01-01]
\npci 0000:00:00.0: bridge window [io disabled]
\npci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
\npci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
\nBAR0 at slot 0 = 0
\nbus=0x0, slot = 0x0
\nres[0]->start = 0
\nres[0]->end = 0
\nres[1]->start = 20200000
\nres[1]->end = 2020ffff
\nres[2]->start = 0
\nres[2]->end = 0
\nres[3]->start = 0
\nres[3]->end = 0
\nres[4]->start = 0
\nres[4]->end = 0
\nres[5]->start = 0
\nres[5]->end = 0
\nbus=0x1, slot = 0x0
\nres[0]->start = 20000000
\nres[0]->end = 200fffff
\nres[1]->start = 0
\nres[1]->end = 0
\nres[2]->start = 0
\nres[2]->end = 0
\nres[3]->start = 0
\nres[3]->end = 0
\nres[4]->start = 0
\nres[4]->end = 0
\nres[5]->start = 0
\nres[5]->end = 0
\nSwitching to clocksource Ralink Systick timer
\nNET: Registered protocol family 2
\nIP route cache hash table entries: 1024 (order: 0, 4096 bytes)
\nTCP established hash table entries: 2048 (order: 2, 16384 bytes)
\nTCP bind hash table entries: 2048 (order: 1, 8192 bytes)
\nTCP: Hash tables configured (established 2048 bind 2048)
\nTCP reno registered
\nUDP hash table entries: 256 (order: 0, 4096 bytes)
\nUDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
\nNET: Registered protocol family 1
\nmsgmni has been set to 113
\nBlock layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
\nio scheduler noop registered (default)
\npcieport 0000:00:00.0: device [14c3:0801] has invalid IRQ; check vendor BIOS
\nRalink gpio driver initialized
\ni2cdrv_major = 218
\nSerial: 8250\/16550 driver, 2 ports, IRQ sharing enabled
\nserial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
\nserial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
\nbrd: module loaded
\nRead GD Flash ID!
\nflash manufacture id: c8, device id 40 17
\nGD25Q64B(c8 40170000) (8192 Kbytes)
\nmtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
\nCreating 5 MTD partitions on “raspi”:
\n0x000000000000-0x000000800000 : “ALL”
\n0x000000000000-0x000000030000 : “Bootloader”
\n0x000000030000-0x000000040000 : “Config”
\n0x000000040000-0x000000050000 : “Factory”
\n0x000000050000-0x000001000000 : “Kernel”
\nmtd: partition “Kernel” extends beyond the end of device “raspi” — size truncated to 0x7b0000
\nrdm_major = 253
\nGMAC1_MAC_ADRH — : 0x000000e0
\nGMAC1_MAC_ADRL — : 0x2051bd6b
\nRalink APSoC Ethernet Driver Initilization. v3.1 256 rx\/tx descriptors allocated, mtu = 1500!
\nGMAC1_MAC_ADRH — : 0x000000e0
\nGMAC1_MAC_ADRL — : 0x2051bd6b
\nPROC INIT OK!
\nPPP generic driver version 2.4.2
\nNET: Registered protocol family 24
\nPPTP driver version 0.8.5<\/p>\n

=== pAd = c014d000, size = 1404512 ===<\/p>\n

<– RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
\n<– RTMPAllocAdapterBlock, Status=0
\nRtmpChipOpsHook(492): Not support for HIF_MT yet!
\nmt7628_init()–>
\nmt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
\ne2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
\nmt_bcn_buf_init(218): Not support for HIF_MT yet!
\n<–mt7628_init()
\nnf_conntrack version 0.5.0 (908 buckets, 3632 max)
\nmatchsize=264
\nIPVS: Registered protocols ()
\nIPVS: Connection hash table configured (size=4096, memory=32Kbytes)
\nIPVS: ipvs loaded.
\nGRE over IPv4 demultiplexor driver
\ngre: can’t add protocol
\nip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
\nTCP cubic registered
\nNET: Registered protocol family 10
\nNET: Registered protocol family 17
\nBridge firewalling registered
\nEbtables v2.0 registered
\nLan Domain: myrepeater.net
\nLan Domain: www.mywifi.net
\nLan Domain: www.myrepeater.net
\nLan Domain: mywifi.net
\nLan Domain: myrepeater.net
\nL2TP core driver, V2.0
\nPPPoL2TP kernel driver, V2.0
\n802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
\nAll bugs added by David S. Miller <davem@redhat.com>
\nWarning: unable to open an initial console.
\nFreeing unused kernel memory: 2480k freed
\nAlgorithmics\/MIPS FPU Emulator v1.5<\/p>\n

,–. <__)
\n `- |________7
\n |`. |\\
\n .–|. \\ |.\\–.
\n \/ j \\ `.7__j__\\ \\
\n| o | (o)____O) |
\n \\ \/ J \\ \/
\n `—‘ `—‘ <\/p>\n

init: can’t log to \/dev\/tty5
\nstarting pid 111, tty ‘\/dev\/ttyS1’: ‘\/bin\/sh’<\/p>\n

BusyBox v1.12.1 (2018-06-13 22:24:34 CST) built-in shell (ash)
\nEnter ‘help’ for a list of built-in commands.<\/p>\n

# Raeth v3.1 (Tasklet,SkbRecycle)<\/p>\n

phy_tx_ring = 0x02d37000, tx_ring = 0xa2d37000<\/p>\n

phy_rx_ring0 = 0x02d38000, rx_ring0 = 0xa2d38000
\nGMAC1_MAC_ADRH — : 0x000000e0
\nGMAC1_MAC_ADRL — : 0x2051bd6b
\nRT305x_ESW: Link Status Changed
\ndevice eth2 entered promiscuous mode
\ndevice eth2.1 entered promiscuous mode
\nTX_BCN DESC a33a6000 size = 320
\nRX[0] DESC a33a9000 size = 1024
\nRX[1] DESC a33aa000 size = 1024
\nE2pAccessMode=2
\ncfg_mode=9
\ncfg_mode=9
\nwmode_band_equal(): Band Equal!
\nAndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
\nAPSDCapable[0]=0
\nAPSDCapable[1]=0
\nAPSDCapable[2]=0
\nAPSDCapable[3]=0
\nAPSDCapable[4]=0
\nAPSDCapable[5]=0
\nAPSDCapable[6]=0
\nAPSDCapable[7]=0
\nAPSDCapable[8]=0
\nAPSDCapable[9]=0
\nAPSDCapable[10]=0
\nAPSDCapable[11]=0
\nAPSDCapable[12]=0
\nAPSDCapable[13]=0
\nAPSDCapable[14]=0
\nAPSDCapable[15]=0
\ndefault ApCliAPSDCapable[0]=0
\nKey1Str is Invalid key length(0) or Type(0)
\nKey2Str is Invalid key length(0) or Type(0)
\nKey3Str is Invalid key length(0) or Type(0)
\nKey4Str is Invalid key length(0) or Type(0)
\nRTMPSetDefaultChannel() : default channel to 1
\nload fw image from fw_header_image
\nAndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
\nFW Version:20151201
\nFW Build Date:20151201183641
\nCmdAddressLenReq:(ret = 0)
\nCmdFwStartReq: override = 1, address = 1048576
\nCmdStartDLRsp: WiFI FW Download Success
\nMtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
\nefuse_probe: efuse = 10000002
\nRtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
\nRtmpEepromGetDefault::e2p_dafault=2
\nRtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
\nNVM is FLASH mode
\n1. Phy Mode = 14
\nCountry Region from e2p = ffff
\ntssi_1_target_pwr_g_band = 30
\n2. Phy Mode = 14
\n3. Phy Mode = 14
\nNICInitPwrPinCfg(11): Not support for HIF_MT yet!
\nNICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
\nmt_mac_init()–>
\nMtAsicInitMac()–>
\nmt7628_init_mac_cr()–>
\nMtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
\n<–mt_mac_init()
\n WTBL Segment 1 info:
\n MemBaseAddr\/FID:0x28000\/0
\n EntrySize\/Cnt:32\/128
\n WTBL Segment 2 info:
\n MemBaseAddr\/FID:0x40000\/0
\n EntrySize\/Cnt:64\/128
\n WTBL Segment 3 info:
\n MemBaseAddr\/FID:0x42000\/64
\n EntrySize\/Cnt:64\/128
\n WTBL Segment 4 info:
\n MemBaseAddr\/FID:0x44000\/128
\n EntrySize\/Cnt:32\/128
\nAntCfgInit(2946): Not support for HIF_MT yet!
\nMCS Set = ff ff 00 00 01
\nMtAsicSetChBusyStat(861): Not support for HIF_MT yet!
\nCmdSlotTimeSet:(ret = 0)
\n[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
\nMtAsicSetRalinkBurstMode(3051): Not support for HIF_MT yet!
\nMtAsicSetPiggyBack(796): Not support for HIF_MT yet!
\nMtAsicSetTxPreamble(3030): Not support for HIF_MT yet!
\nThe 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
\nMtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
\nMain bssid = 00:e0:20:51:bd:6d
\n<==== rt28xx_init, Status=0
\n@@@ ed_monitor_exit : ===>
\n@@@ ed_monitor_exit : <===
\nmt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
\nWiFi Startup Cost (ra0): 3.764s
\ndevice ra0 entered promiscuous mode
\nregister rt2860<\/p>\n

=== pAd = c0782000, size = 2162080 ===<\/p>\n

<– RTMPAllocTxRxRingMemory, Status=0
\n<– RTMPAllocAdapterBlock, Status=0
\npAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000!
\ndevice_id =0x7662
\n==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
\n====> mt76x2_ePA_per_rate_compensate_init: 5868 is_ePA: 1
\nE2pAccessMode=2
\ncfg_mode=14
\ncfg_mode=14
\nwmode_band_equal(): Band Not Equal!
\nAPSDCapable[0]=0
\nAPSDCapable[1]=0
\nAPSDCapable[2]=0
\nAPSDCapable[3]=0
\nAPSDCapable[4]=0
\nAPSDCapable[5]=0
\nAPSDCapable[6]=0
\nAPSDCapable[7]=0
\nAPSDCapable[8]=0
\nAPSDCapable[9]=0
\nAPSDCapable[10]=0
\nAPSDCapable[11]=0
\nAPSDCapable[12]=0
\nAPSDCapable[13]=0
\nAPSDCapable[14]=0
\nAPSDCapable[15]=0
\ndefault ApCliAPSDCapable[0]=0
\nKey1Str is Invalid key length(0) or Type(0)
\nKey2Str is Invalid key length(0) or Type(0)
\nKey3Str is Invalid key length(0) or Type(0)
\nKey4Str is Invalid key length(0) or Type(0)
\nWiFi Mcast disabled=0
\nRtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
\nNVM is FLASH mode (pAd->flash_offset = 0x48000)
\nget_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
\nbuild time =
\n20141115060606a
\nrom patch for E3 IC<\/p>\n

platform =
\nALPS
\nhw\/sw version =
\n??
\npatch version = <\/p>\n

FW Version:0.0.00 Build:1
\nBuild Time:201507311614____
\nfw for E3 IC
\nRX[0] DESC a2f9f000 size = 4096
\nRX[1] DESC a2fc8000 size = 4096
\nE2pAccessMode=2
\ncfg_mode=14
\ncfg_mode=14
\nwmode_band_equal(): Band Not Equal!
\nAPSDCapable[0]=0
\nAPSDCapable[1]=0
\nAPSDCapable[2]=0
\nAPSDCapable[3]=0
\nAPSDCapable[4]=0
\nAPSDCapable[5]=0
\nAPSDCapable[6]=0
\nAPSDCapable[7]=0
\nAPSDCapable[8]=0
\nAPSDCapable[9]=0
\nAPSDCapable[10]=0
\nAPSDCapable[11]=0
\nAPSDCapable[12]=0
\nAPSDCapable[13]=0
\nAPSDCapable[14]=0
\nAPSDCapable[15]=0
\ndefault ApCliAPSDCapable[0]=0
\nKey1Str is Invalid key length(0) or Type(0)
\nKey2Str is Invalid key length(0) or Type(0)
\nKey3Str is Invalid key length(0) or Type(0)
\nKey4Str is Invalid key length(0) or Type(0)
\nWiFi Mcast disabled=0
\n1. Phy Mode = 49
\nget_chl_grp:illegal channel (167)
\nget_chl_grp:illegal channel (167)
\nget_chl_grp:illegal channel (169)
\nget_chl_grp:illegal channel (169)
\nget_chl_grp:illegal channel (171)
\nget_chl_grp:illegal channel (171)
\ndrivers\/net\/wireless\/rlt_wifi_ap\/..\/rlt_wifi\/chips\/mt76x2.c:3028 assert (ad->TxPower[choffset].Channel == 42)failed
\nCountry Region from e2p = ffff
\nmt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
\nmt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3
\nmt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
\nmt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
\nmt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
\nmt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
\nmt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0
\n2. Phy Mode = 49
\n3. Phy Mode = 49
\nandes_pci_fw_init
\n0x1300 = 00073200
\nAntCfgInit: primary\/secondary ant 0\/1
\nandes_load_cr:cr_type(2)
\nChipStructAssign(): MT76x2 hook !
\nMCS Set = ff ff 00 00 01
\nmt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155
\nTX0 power compensation = 0x38
\nTX1 power compensation = 0x38
\nAPStartUp(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
\nmt76x2_calibration(channel = 155)
\nMain bssid = 00:e0:20:51:bd:6e
\nmt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c
\nmt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c
\nmt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27
\nmt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27
\noriginal vga value(chain0) = 5c
\noriginal vga value(chain1) = 5c
\n<==== rt28xx_init, Status=0
\nget_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
\nRTMPDrvOpen(1):Check if PDMA is idle!
\nRTMPDrvOpen(2):Check if PDMA is idle!
\ndevice rai0 entered promiscuous mode
\nbr0: port 3(rai0) entering learning state
\nbr0: port 3(rai0) entering learning state
\nbr0: port 2(ra0) entering learning state
\nbr0: port 2(ra0) entering learning state
\nbr0: port 1(eth2.1) entering learning state
\nbr0: port 1(eth2.1) entering learning state
\nbr0: port 3(rai0) entering forwarding state
\nbr0: port 2(ra0) entering forwarding state
\nbr0: port 1(eth2.1) entering forwarding state
\nled=13, on=1, off=4000, blinks,=1, reset=1, time=4000<\/p>\n

\u51c6\u5907\u5f00\u5e72\u4e86\uff0c\u5148\u70e7\u5199\u4e0d\u6b7b\u7684UBOOT-Breed\u3002
\n\u6211\u51c6\u5907\u7528UBUNTU\u5bf9\u8fd9\u5757\u677f\u5b50\u5237\u673a\uff0c\u5148\u5728UBUNTU\u4e0a\u5b89\u88c5tftp\uff1a<\/p>\n

1.\u5b89\u88c5tftp
\nsudo apt-get install tftp-hpa tftpd-hpa xinetd<\/p>\n

2. \u5efa\u7acb\u76ee\u5f55
\nsudo mkdir \/tftpboot # \u8fd9\u662f\u5efa\u7acbtftp\u4f20\u8f93\u76ee\u5f55\u3002<\/span> sudo chmod 777 \/tftpboot
\nsudo touch test.txt # test.txt\u6587\u4ef6\u6700\u597d\u8f93\u5165\u5185\u5bb9\u4ee5\u4fbf\u533a\u5206<\/p>\n

3. \u914d\u7f6e
\n# sudo gedit \/etc\/default\/tftpd-hpa
\nTFTP_USERNAME=”tftp”
\nTFTP_DIRECTORY=”\/tftpboot” # \u8fd9\u91cc\u662f\u4f60\u7684tftpd-hpa\u7684\u670d\u52a1\u76ee\u5f55,\u8fd9\u4e2a\u60f3\u5efa\u7acb\u5728\u54ea\u91cc\u90fd\u884c
\nTFTP_ADDRESS=”0.0.0.0:69″
\nTFTP_OPTIONS=”-l -c -s” # \u8fd9\u91cc\u662f\u9009\u9879,-c\u662f\u53ef\u4ee5\u4e0a\u4f20\u6587\u4ef6\u7684\u53c2\u6570\uff0c-s\u662f\u6307\u5b9atftpd-hpa\u670d\u52a1\u76ee\u5f55\uff0c\u4e0a\u9762\u5df2\u7ecf\u6307\u5b9a<\/p>\n

4. \u91cd\u542f\u670d\u52a1<\/span> sudo service tftpd-hpa restart # \u542f\u52a8\u670d\u52a1\uff0c\u8fd9\u91cc\u8981\u6ce8\u610f\uff0c\u91c7\u7528\u7684\u72ec\u7acb\u670d\u52a1\u5f62\u5f0f\u3002<\/p>\n

5. \u6d4b\u8bd5
\n# cd \/home\/myfolder
\n# tftp localhost #localhost \u8868\u793a\u672c\u673a
\ntftp>get test.txt \/\/test.txt \u662f\u4e4b\u524d\u5728 \/tftpboot \u76ee\u5f55\u4e0b\u65b0\u5efa\u7684\u6587\u4ef6
\ntftp>q<\/p>\n

#\u9000\u51fa\u540e\uff0c\u5728\u76ee\u5f55\u4e0b\u4f1a\u6709\u4e00\u4e2atest.txt\u6587\u4ef6\uff0c\u8868\u793atftp\u670d\u52a1\u5668\u5b89\u88c5\u6210\u529f\uff01 <\/p>\n

\u76ee\u524d\u6211\u6709\u4e00\u53f0windows\u7535\u8111\uff0c\u5b89\u88c5\u4e86\u4e32\u53e3\u5de5\u5177SecureCRT\uff0c\u901a\u8fc7\u4e32\u53e3\u63a5\u5230\u8def\u7531\u5668PCB\u4e0a\u67e5\u770b\u4e32\u53e3\u4fe1\u606f\uff0c\u4ee5\u53ca\u4e0b\u4e32\u53e3\u547d\u4ee4\u3002<\/p>\n

\u53e6\u5916\u4e00\u53f0UBUNTU\u7535\u8111\uff0c\u7528\u4e0a\u9762\u7684\u65b9\u6cd5\u5b89\u88c5\u4e86TFTP\u670d\u52a1\uff0c\u540c\u65f6\u7528\u4e00\u6839\u7f51\u7ebf\u628aUBUNTU\u548c\u8def\u7531\u5668PCB\u677f\u5b50\u8fde\u63a5\u8d77\u6765\u3002<\/p>\n

\u8fd9\u65f6UBUNTU\u7535\u8111\u83b7\u5f97IP\u662f192.168.1.100\uff0c\u8def\u7531\u5668PCB\u677f\u5b50IP\u662f\uff1a192.168.1.253\uff08\u901a\u8fc7\u4e32\u53e3\u6267\u884c\u547d\u4ee4ifconfig\uff0c\u5982\u4e0b\uff09\uff0c<\/p>\n

\u6211\u770b\u5230\u6590\u8bafk1\u7684\u914d\u7f6e\u548c\u6211\u7684\u8fd9\u5757PCB\u914d\u7f6e\u5dee\u4e0d\u591a\uff0c\u4e8e\u662f\u4ece\u7f51\u4e0a\u627e\u4e2a\u6590\u8bafk1\u7684Breed\u5237\u5165\u3002<\/p>\n

# ifconfig
\nbr0 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6B
\n inet addr:192.168.1.253 Bcast:192.168.1.255 Mask:255.255.255.0
\n inet6 addr: fe80::2e0:20ff:fe51:bd6b\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:99 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:9726 (9.4 KiB) TX bytes:3874 (3.7 KiB)<\/p>\n

eth2 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6B
\n inet6 addr: fe80::2e0:20ff:fe51:bd6b\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:101 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:446 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:1000
\n RX bytes:12212 (11.9 KiB) TX bytes:243336 (237.6 KiB)
\n Interrupt:3 <\/p>\n

eth2.1 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6B
\n inet6 addr: fe80::2e0:20ff:fe51:bd6b\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:101 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:10798 (10.5 KiB) TX bytes:4232 (4.1 KiB)<\/p>\n

eth2.2 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6C
\n inet6 addr: fe80::2e0:20ff:fe51:bd6c\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:0 (0.0 B) TX bytes:238686 (233.0 KiB)<\/p>\n

lo Link encap:Local Loopback
\n inet addr:127.0.0.1 Mask:255.0.0.0
\n inet6 addr: ::1\/128 Scope:Host
\n UP LOOPBACK RUNNING MTU:16436 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)<\/p>\n

ra0 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6D
\n inet6 addr: fe80::2e0:20ff:fe51:bd6d\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:1000
\n RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
\n Interrupt:4 <\/p>\n

rai0 Link encap:Ethernet HWaddr 00:E0:20:51:BD:6E
\n inet6 addr: fe80::2e0:20ff:fe51:bd6e\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:1000
\n RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
\n Interrupt:2 <\/p>\n

#\u5728ubuntu\u4e0a\u6253\u5f00\u547d\u4ee4\u63d0\u793a\u7b26\uff0c\u8f93\u5165telnet 192.168.2.253\uff0c\u7528\u6237\u540d\u548c\u5bc6\u7801\u5747\u662fadmin<\/p>\n

#\u7136\u540e\u8f93\u5165
\ncd \/tmp
\ntftp -g -l \/tmp\/uboot.bin -r uboot.bin 192.168.2.100
\nmtd_write write uboot.bin Bootloader<\/p>\n

#\u7b49\u5f85\u4e00\u4e24\u79d2\uff0c\u5237\u5165Breed\u3002<\/p>\n

\u5982\u679c\u6240\u6599\uff0c\u677f\u5b50\u53d8\u7816\uff0c\u5f00\u673a\u4e32\u53e3\u65e0\u4efb\u4f55\u8f93\u51fa\u3002<\/p>\n

\u65e0\u5948\uff0c\u53ea\u80fd\u628aSNOR Flash\u62c6\u4e0b\uff0c\u7528\u70e7\u5f55\u5668\u5347\u7ea7\u3002<\/p><\/div>\n

\u8fd9\u6b21\u6211\u627e\u5230\u7684\u662f\u8fd9\u4e2abootloader\u8bd5\u8bd5\u8fd0\u6c14\uff1a<\/p>\n

http:\/\/downloads.openwrt.org.cn\/PandoraBox\/MT7628AN_EVB\/u-boot\/u-boot-pandorabox-mt7628an-evb-20150518.bin <\/p>\n

\u70e7\u5f55\u5668\u70e7\u5b8c\uff0c\u710a\u56de\uff0c\u63a5\u4e0a\u4e32\u53e3\u7ebf\uff0c\u6ce2\u7279\u7387\u8bbe\u7f6e\u6210115200\uff0c\u4e0a\u7535\u5f00\u673a\uff0c\u6709\u6b63\u5e38\u7684\u4fe1\u606f\u6253\u5370\u51fa\uff1a<\/p>\n

[04020C0D][04020C0D]
\nDDR Calibration DQS reg = 00008787<\/p>\n

U-Boot 1.1.3 (May 18 2015 – 14:37:16)<\/p>\n

SoC:MediaTek MT7628
\nDRAM: Found DDR2 Memory.
\nTEST-0 256M:
\n CFG0:0x249CE2E5
\n CFG1:0x223A2323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nTEST-1 128M:
\n CFG0:0x249B42E5
\n CFG1:0x22362323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nTEST-2 64M:
\n CFG0:0x249AA2E5
\n CFG1:0x22322323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nDone,DDR2 is 64 MB
\nrelocate_code Pointer at: 83fa8000
\nflash manufacture id: c8, device id 40 17
\nFlash:GD25Q64B Size:8MB
\n*** Warning – bad CRC, using default environment<\/p>\n

_______________________________________________________________
\n| ____ _ ____ |
\n| | _ \\ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
\n| | |_) \/ _` | ‘_ \\ \/ _` |\/ _ \\| ‘__\/ _` | _ \\ \/ _ \\ \\\/ \/ |
\n| | __\/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
\n| |_| \\__,_|_| |_|\\__,_|\\___\/|_| \\__,_|____\/ \\___\/_\/\\_\\ |
\n| |
\n| PandoraBox Ralink\/MTK Platform |
\n| The best solution for you |
\n| Copyright 2015 D-Team Technology Co.,Ltd. SZ |
\n| Board:Ralink RT305x |
\n| |
\n| lintel<lintel.huang@gmail.com> |
\n|______________________________________________________________|<\/p>\n

===============Board Info==================
\nCPU Frequency:575MHz
\nDetected Memory:64MiB
\nBootloader Version:4.3.1.0
\nicache: sets:512, ways:4, linesz:32 ,total:64KiB
\ndcache: sets:256, ways:4, linesz:32 ,total:32KiB
\n============================================
\nRESET MT7628 PHY!!!!!!
\nGSW VLAN:LLLW
\nGPIO_MODE init:
\n I2C:GPIO
\n REFCLK0:GPIO
\n NAND\/SD:GPIO
\n WDT_RST:GPIO
\nGPIO_MODE_REGs: 0x571544d5
\nREADY_LED_BIT:37.
\nPlease choose the operation:
\n 1: Load system code to SDRAM via TFTP.
\n 2: Load system code then write to Flash via TFTP.
\n 3: Boot system code via Flash (default).
\n 4: Entr boot command line interface.
\n 7: Load Boot Loader code then write to Flash via Serial.
\n 9: Load Boot Loader code then write to Flash via TFTP.
\n 0 <\/p>\n

3: System Boot system code via Flash.<\/p>\n

Press Reset button enter upgrade mode!
\n## Booting image at bc050000 …
\nBad Magic Number,FFFFFFFF <\/p>\n

Starting httpd to update firmware…
\n______________________________________________________
\n| |
\n| Recovery Module v2.0 |
\n| |
\n| Note:Please Use Web Browser Upgrade the Firmware ! |
\n| |
\n| Copyright 2014 D-Team Technology Co.,Ltd. SZ |
\n| lintel<lintel.huang@gmail.com> |
\n|____________________________________________________|<\/p>\n

[Kernel]uOS Version: v1.2
\n[TCP\/IP]ETH0 MAC:FF:FF:FF:FF:FF:FF
\n[TCP\/IP]IP:192.168.1.1
\n[TCP\/IP]Netmask:255.255.255.0
\n[TCP\/IP]Default Router:0.0.0.0
\n[DHCPD]Server IP:192.168.1.1<\/p>\n

NetTxPacket = 0x83FE1380.
\nTrying Eth0 (10\/100-M)<\/p>\n

Waitting for RX_DMA_BUSY status Start… done<\/p>\n

ETH_STATE_ACTIVE!!
\n[Kernel]Enter Network Loop!
\n[LED]Thread started!! <\/p>\n

\u628aUBUNTU\u7535\u8111\u548c\u8def\u7531\u5668\u901a\u8fc7\u6709\u7ebf\u76f8\u8fde\uff0cUBUNTU\u4f1a\u63d0\u793a\u6709\u7f51\u7edc\u8fde\u63a5\u6210\u529f\uff0c\u8f93\u5165IP192.168.1.1\u53ef\u6253\u5f00bootloader\u5237\u56fa\u4ef6\u7684\u7f51\u9875\uff08\u770b\u7f51\u4e0a\u8bf4\u8981\u5148\u6309\u4f4freset\u952e\u518d\u4e0a\u7535\uff0c\u5982\u679c\u53ea\u5b58\u5728uboot\u7684\u56fa\u4ef6\u4e0d\u9700\u8981\u6309\u952e\uff0c\u5982\u679c\u91cc\u9762\u6709\u70e7\u5199\u7cfb\u7edf\u56fa\u4ef6\uff0c\u4e0b\u6b21\u60f3\u8fdbuboot\u70e7\u5176\u4ed6\u56fa\u4ef6\uff0c\u624d\u9700\u8981\u6309\u4f4freset key\uff09\u3002<\/p>\n

#\u5728openwrt\u5b98\u65b9\u7f51\u7ad9\u4e0a\uff0c\u6211\u770b\u5230\u4e0b\u9762\u7684\u4ea7\u54c1\uff08Archer C50 v3\uff09\u548c\u6211\u7684\u786c\u4ef6\u914d\u7f6e\u4e00\u6837\u3002
\nhttps:\/\/openwrt.org\/toh\/tp-link\/archer-c50<\/p>\n

#\u4f46\u662f\u6211\u4e0b\u8f7d\u4e0b\u6765\u540e\uff0c\u65e0\u6cd5\u70e7\u5f55\uff0c\u63d0\u793a\u6821\u9a8c\u5931\u8d25
\nhttp:\/\/downloads.openwrt.org\/releases\/18.06.1\/targets\/ramips\/mt76x8\/openwrt-18.06.1-ramips-mt76x8-tplink_c50-v3-squashfs-tftp-recovery.bin <\/p>\n

\nOpenWRT\u5b98\u7f51\u6709\u4e2a\u95ee\u9898\uff0c\u641c\u7d22CPU\u578b\u53f7\u627e\u51fa\u6765\u7684\u5185\u5bb9\u5be5\u5be5\u65e0\u51e0\u3002\u53ef\u4ee5\u7528\u4e0b\u9762\u7684\u65b9\u6cd5\u67e5\u627e\uff1a\n <\/div>\n

#Table of Hardware\uff1aThis is the main Table of Hardware, listing all devices that are supported by OpenWrt.
\nhttps:\/\/openwrt.org\/toh\/start
\n#Table of Hardware: Full details\u3002This table shows full hardware details for all devices listed in the Table of Hardware.
\nhttps:\/\/openwrt.org\/toh\/views\/toh_extended_all<\/p>\n

#\u8fd9\u4e2a\u6bd4\u8f83\u597d\u7528\uff0c\u6309\u7167\u5404\u79cd\u5173\u952e\u5b57\u641c\u7d22\uff1a
\nhttps:\/\/openwrt.org\/toh\/views\/dataclouds <\/p>\n

\u968f\u540e\u6211\u5728\u4e0b\u9762\u7684\u7f51\u5740\u4e2d\u627e\u5230\u4e86\u89e3\u51b3\u529e\u6cd5\uff0c<\/div>\n

#\u4e0b\u9762\u7684boot\u548c\u56fa\u4ef6\u62ef\u6551\u4e86\u6211\u7684\u677f\u5b50\uff0cuboot\u548c\u56fa\u4ef6\u90fd\u9a8c\u8bc1\u53ef\u7528
\nhttp:\/\/downloads.openwrt.org.cn\/PandoraBox\/MT7628AN_EVB\/<\/p>\n

#\u4e0b\u9762\u8fd9\u4e2a\u56fa\u4ef6\u70e7\u8fdb\u53bb\u540e\uff0c\u6700\u540e\u4f1a\u6b7b\u673a
\nhttp:\/\/downloads.openwrt.org.cn\/PandoraBox\/MT7628AN_EVB\/PandoraBox-ralink-mt7628-mt7628an-evb-squashfs-sysupgrade-r865-20150519.bin<\/p>\n

#\u4e0b\u9762\u8fd9\u4e2a\u8fd9\u4e2a\u56fa\u4ef6\uff0c\u81f3\u5c11\u80fd\u8dd1\u8d77\u6765
\nhttp:\/\/downloads.openwrt.org.cn\/PandoraBox\/MT7628AN_EVB\/PandoraBox-ralink-mt7628-mt7628an-evb-squashfs-sysupgrade-r858-20150518.bin<\/p>\n

\u7528\u4e32\u53e3\u767b\u5f55\uff0c\u6216\u8005\u7528192.168.1.1\u767b\u5f55\u7f51\u9875\u65f6\uff0c\u7528\u6237\u540droot,\u521d\u59cb\u5bc6\u7801admin <\/p>\n

#pandorabox\u7684SDK\u4e0eIPK\u5e94\u7528\u7a0b\u5e8f\u5728\u8fd9\u91cc\u4e0b\u8f7d\uff1a
\nhttps:\/\/downloads.pangubox.com\/pandorabox\/18.10\/targets\/ralink\/mt7628\/<\/p>\n

#\u7f16\u8bd1pandorabox
\nhttps:\/\/blog.csdn.net\/lvshaorong\/article\/details\/62215033<\/p>\n

\u5f00\u673a\u6210\u529f\uff0c\u6253\u5370\u4fe1\u606f\u5982\u4e0b\uff1a<\/p>\n

……………………………………………………………………..
\n……………………………………………………………………..
\n.
\n.
\nDone!<\/p>\n

[kernel]Firmware upgrade done!
\n[httpd]Reboot!!!
\n[kernel]Signal pending 0.
\n[Kernel]Signal ACK and clean.
\n[Kernel]reboot Signal detect!!
\n [04020C0D][04020C0D]
\nDDR Calibration DQS reg = 00008787<\/p>\n

U-Boot 1.1.3 (May 18 2015 – 14:37:16)<\/p>\n

SoC:MediaTek MT7628
\nDRAM: Found DDR2 Memory.
\nTEST-0 256M:
\n CFG0:0x249CE2E5
\n CFG1:0x223A2323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nTEST-1 128M:
\n CFG0:0x249B42E5
\n CFG1:0x22362323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nTEST-2 64M:
\n CFG0:0x249AA2E5
\n CFG1:0x22322323
\n CFG2:0x68000C43
\n CFG3:0x00000452
\n CFG4:0x0000000A
\nDone,DDR2 is 64 MB
\nrelocate_code Pointer at: 83fa8000
\n******************************
\nSoftware System Reset Occurred
\n******************************
\nflash manufacture id: c8, device id 40 17
\nFlash:GD25Q64B Size:8MB
\n*** Warning – bad CRC, using default environment<\/p>\n

_______________________________________________________________
\n| ____ _ ____ |
\n| | _ \\ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
\n| | |_) \/ _` | ‘_ \\ \/ _` |\/ _ \\| ‘__\/ _` | _ \\ \/ _ \\ \\\/ \/ |
\n| | __\/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
\n| |_| \\__,_|_| |_|\\__,_|\\___\/|_| \\__,_|____\/ \\___\/_\/\\_\\ |
\n| |
\n| PandoraBox Ralink\/MTK Platform |
\n| The best solution for you |
\n| Copyright 2015 D-Team Technology Co.,Ltd. SZ |
\n| Board:Ralink RT305x |
\n| |
\n| lintel<lintel.huang@gmail.com> |
\n|______________________________________________________________|<\/p>\n

===============Board Info==================
\nCPU Frequency:575MHz
\nDetected Memory:64MiB
\nBootloader Version:4.3.1.0
\nicache: sets:512, ways:4, linesz:32 ,total:64KiB
\ndcache: sets:256, ways:4, linesz:32 ,total:32KiB
\n============================================
\nRESET MT7628 PHY!!!!!!
\nGSW VLAN:LLLW
\nGPIO_MODE init:
\n I2C:GPIO
\n REFCLK0:GPIO
\n NAND\/SD:GPIO
\n WDT_RST:GPIO
\nGPIO_MODE_REGs: 0x55154415
\nREADY_LED_BIT:37.
\nPlease choose the operation:
\n 1: Load system code to SDRAM via TFTP.
\n 2: Load system code then write to Flash via TFTP.
\n 3: Boot system code via Flash (default).
\n 4: Entr boot command line interface.
\n 7: Load Boot Loader code then write to Flash via Serial.
\n 9: Load Boot Loader code then write to Flash via TFTP.
\n 0 <\/p>\n

3: System Boot system code via Flash.<\/p>\n

Press Reset button enter upgrade mode!
\n## Booting image at bc050000 …
\n Image Name: PabdoraBox Linux-3.14.42
\n Image Type: MIPS Linux Kernel Image (lzma compressed)
\n Data Size: 1134785 Bytes = 1.1 MB
\n Load Address: 80000000
\n Entry Point: 80000000
\n Verifying Checksum … OK
\n Uncompressing Kernel Image … OK
\nNo initrd
\n## Transferring control to Linux (at address 80000000) …
\n## Giving linux memsize in MB, 64<\/p>\n

Starting kernel …<\/p>\n

PandoraBox For Ralink\/MTK APSoC. Copyright 2013-2014 D-Team Technology SZ <\/p>\n

LINUX started…<\/p>\n

THIS IS ASIC
\n[ 0.000000] Linux version 3.14.42 (lintel@PandoraBox-Server) (gcc version 4.8.3 (PandoraBox\/Linaro GCC 4.8-2014.04 r775) ) #32 Mon May 18 19:15:21 CST 2015
\n[ 0.000000] PandoraBox CPUID Module for Ralink\/MTK SoC v1.1.
\n[ 0.000000] MediaTek MT7628 pkg:BGA rev:1 eco:2 CPU:575MHz, Bus:191MHz Uart:191MHz
\n[ 0.000000] CPU running in Little Endian
\n[ 0.000000] Board VLAN:LLLLW
\n[ 0.000000] Flash:SPI Size: 8MB
\n[ 0.000000] DRAM: 64MB DDR2 16 bits
\n[ 0.000000] Kernel Support [PCI] [USB]
\n[ 0.000000]
\n[ 0.000000] MIPS CPU sleep mode enabled.
\n[ 0.000000] bootconsole [early0] enabled
\n[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
\n[ 0.000000] Software DMA cache coherency
\n[ 0.000000] Determined physical RAM map:
\n[ 0.000000] memory: 04000000 @ 00000000 (usable)
\n[ 0.000000] Initrd not found or empty – disabling initrd
\n[ 0.000000] Zone ranges:
\n[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
\n[ 0.000000] Movable zone start for each node
\n[ 0.000000] Early memory node ranges
\n[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
\n[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
\n[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
\n[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
\n[ 0.000000] Kernel command line: pause_on_oops=10 noresume board=MT7628A_EVB console=ttyS1,115200 rootfstype=squashfs,jffs2
\n[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
\n[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
\n[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
\n[ 0.000000] Writing ErrCtl register=0003cd70
\n[ 0.000000] Readback ErrCtl register=0003cd70
\n[ 0.000000] Memory: 61392K\/65536K available (2443K kernel code, 130K rwdata, 504K rodata, 176K init, 253K bss, 4144K reserved)
\n[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
\n[ 0.000000] NR_IRQS:256
\n[ 0.000000] console [ttyS1] enabled
\n[ 0.000000] console [ttyS1] enabled
\n[ 0.000000] bootconsole [early0] disabled
\n[ 0.000000] bootconsole [early0] disabled
\n[ 0.010000] Calibrating delay loop… 385.84 BogoMIPS (lpj=1929216)
\n[ 0.070000] pid_max: default: 32768 minimum: 301
\n[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
\n[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
\n[ 0.090000] pinctrl core: initialized pinctrl subsystem
\n[ 0.090000] NET: Registered protocol family 16
\n[ 0.100000] Ralink\/MTK BootROM maped.
\n[ 0.100000] Generic GPIO Driver for MediaTek MT7628 Board. Copyright lintel 2005-2013
\n[ 0.110000] MT7628-GPIO0:registering 31 irq handlers
\n[ 0.110000] MT7628-GPIO1:registering 31 irq handlers
\n[ 0.120000] MT7628-GPIO3:registering 31 irq handlers
\n[ 0.120000] MIPS: machine is MediaTek MT7628A Evaluation Board
\n[ 0.130000] ralink_register_flash:SPI Flash.
\n[ 0.130000] MT762x:SDHC Interface registered.
\n[ 0.130000] Ralink\/MTK PinCtrl registered.
\n[ 0.140000] Generic PinCtrl Driver for MediaTek MT7628 Board. Copyright lintel 2005-2015
\n[ 0.140000] ralink-pinmux ralink-pinmux: invalid group “pwm0” for function “sdhc”
\n[ 0.150000] ralink-pinmux ralink-pinmux: invalid group “pwm1” for function “sdhc”
\n[ 0.150000] PINCTRL:add 31 pins for MT7628-PINCTRL0.
\n[ 0.160000] PINCTRL:add 31 pins for MT7628-PINCTRL1.
\n[ 0.160000] PINCTRL:add 31 pins for MT7628-PINCTRL2.
\n[ 0.170000] GPIO_MODE_REG:0x55154415
\n[ 1.280000] bio: create slab <bio-0> at 0
\n[ 1.280000] PCI host bridge to bus 0000:00
\n[ 1.290000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
\n[ 1.290000] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff]
\n[ 1.300000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
\n[ 1.300000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
\n[ 1.310000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
\n[ 1.310000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
\n[ 1.320000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
\n[ 1.320000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
\n[ 1.330000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
\n[ 1.330000] pci 0000:00:00.0: PCI bridge to [bus 01]
\n[ 1.340000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
\n[ 1.340000] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
\n[ 1.350000] PCI Bus 1 slot 0 mapping to IRQ2.
\n[ 1.350000] Switched to clocksource Ralink\/MTK 50kHz Systick timer
\n[ 1.360000] NET: Registered protocol family 2
\n[ 1.360000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
\n[ 1.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
\n[ 1.370000] TCP: Hash tables configured (established 1024 bind 1024)
\n[ 1.380000] TCP: reno registered
\n[ 1.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
\n[ 1.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
\n[ 1.400000] NET: Registered protocol family 1
\n[ 1.400000] Ralink SoC clocks api init.
\n[ 1.410000] mips hpt frequency:287500000HZ
\n[ 1.410000] Ralink\/MTK APSoC GPIO Resource maped.
\n[ 1.420000] Load Ralink Timer0 Module
\n[ 1.420000] Load Ralink Timer1 Module
\n[ 1.420000] Load Ralink Timer2 Module
\n[ 1.430000] MTK\/Ralink EHCI\/OHCI init.
\n[ 1.430000] futex hash table entries: 256 (order: -1, 3072 bytes)
\n[ 1.460000] squashfs: version 4.0 (2009\/01\/31) Phillip Lougher
\n[ 1.460000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
\n[ 1.470000] msgmni has been set to 119
\n[ 1.480000] io scheduler noop registered
\n[ 1.480000] io scheduler deadline registered (default)
\n[ 1.490000] Serial: 8250\/16550 driver, 4 ports, IRQ sharing disabled
\n[ 1.490000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21, base_baud = 2500000) is a 16550A
\n[ 1.500000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
\n[ 1.510000] serial8250: ttyS2 at MMIO 0x10000e00 (irq = 22, base_baud = 0) is a 16550A
\n[ 1.520000] Enable Ralink GDMA Controller Module
\n[ 1.530000] GDMA IP Version=3
\n[ 1.540000] brd: module loaded
\n[ 1.550000] flash manufacture id: c8, device id 40 17
\n[ 1.550000] GD25Q64B(c8 4017c840) (8192 Kbytes)
\n[ 1.560000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
\n[ 1.570000] Creating 5 MTD partitions on “raspi”:
\n[ 1.570000] 0x000000000000-0x000000030000 : “u-boot”
\n[ 1.580000] 0x000000030000-0x000000040000 : “u-boot-env”
\n[ 1.590000] 0x000000040000-0x000000050000 : “Factory”
\n[ 1.590000] 0x000000000000-0x000000800000 : “fullflash”
\n[ 1.600000] 0x000000050000-0x000001000000 : “firmware”
\n[ 1.610000] mtd: partition “firmware” extends beyond the end of device “raspi” — size truncated to 0x7b0000
\n[ 1.630000] 3 uimage-fw partitions found on MTD device firmware
\n[ 1.640000] 0x000000050000-0x000000165101 : “kernel”
\n[ 1.640000] mtd: partition “kernel” must either start or end on erase block boundary or be smaller than an erase block — forcing read-only
\n[ 1.660000] 0x000000165101-0x0000007e0000 : “rootfs”
\n[ 1.660000] mtd: partition “rootfs” must either start or end on erase block boundary or be smaller than an erase block — forcing read-only
\n[ 1.680000] mtd: device 6 (rootfs) set to be root filesystem
\n[ 1.680000] 1 squashfs-split partitions found on MTD device rootfs
\n[ 1.690000] 0x000000540000-0x0000007e0000 : “rootfs_data”
\n[ 1.690000] 0x0000007e0000-0x000000800000 : “panic_oops”
\n[ 1.700000] mtdoops: Attached to MTD device 8
\n[ 1.710000] rdm_major = 252
\n[ 1.720000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
\n[ 1.720000] GMAC1_MAC_ADRH — : 0x0000000c
\n[ 1.730000] GMAC1_MAC_ADRL — : 0x43288074
\n[ 1.730000] Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx\/tx descriptors allocated, mtu = 1500!
\n[ 1.740000] Feature:{HW_CSO}
\n[ 1.740000] EEPROM:Read from [Factory] offset 0x28,length 0x6.
\n[ 1.750000] GMAC1_MAC_ADRH — : 0x0000000c
\n[ 1.750000] GMAC1_MAC_ADRL — : 0x432880bc
\n[ 1.760000] PROC INIT OK!
\n[ 1.760000] rt305x switch driver registered.
\n[ 1.760000] rt305x-esw default vlans:wllll
\n[ 1.770000] Ralink APSoC Hardware Watchdog Timer
\n[ 1.770000] TCP: cubic registered
\n[ 1.780000] TCP: westwood registered
\n[ 1.780000] TCP: hybla registered
\n[ 1.780000] TCP: htcp registered
\n[ 1.790000] NET: Registered protocol family 17
\n[ 1.790000] Bridge firewalling registered
\n[ 1.800000] Ebtables v2.0 registered
\n[ 1.800000] 8021q: 802.1Q VLAN Support v1.8
\n[ 1.810000] PandoraBox Mass Storage accelerater v1.2
\n[ 1.820000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
\n[ 1.820000] Freeing unused kernel memory: 176K (80304000 – 80330000)
\n[ 3.080000] init: Console is alive
\n[ 3.080000] Started WatchDog Timer.
\n[ 3.080000] init: – watchdog –
\n[ 5.450000] usbcore: registered new interface driver usbfs
\n[ 5.460000] usbcore: registered new interface driver hub
\n[ 5.460000] usbcore: registered new device driver usb
\n[ 5.470000] exFAT: Version 1.2.9
\n[ 5.520000] ufsd: module license ‘Commercial product’ taints kernel.
\n[ 5.520000] Disabling lock debugging due to kernel taint
\n[ 5.540000] ufsd: driver (8.6, May 15 2015 17:30:12, LBD=ON, delalloc, ioctl, bdi) loaded at c02b6000
\n[ 5.540000] NTFS (with native replay) support included
\n[ 5.540000] optimized: speed
\n[ 5.540000] Built for PandoraBox 2013-12-27
\n[ 5.540000]
\n[ 5.560000] PandoraBox Button Driver init
\n[ 5.570000] Button [reset] mapped to GPIO38 and IRQ65
\n[ 5.580000] SCSI subsystem initialized
\n[ 5.590000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
\n[ 5.600000] ehci-platform: EHCI generic platform driver
\n[ 5.630000] MT7628 USB Frequency Calibration start!
\n[ 5.650000] FM_OUT value: u4FmOut = 0(0x00000000)
\n[ 5.670000] FM_OUT value: u4FmOut = 134(0x00000086)
\n[ 5.670000] FM detection done! loop = 1
\n[ 5.690000] SR calibration value u1SrCalVal = 6
\n[ 5.690000] ehci-platform ehci-platform: EHCI Host Controller
\n[ 5.700000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
\n[ 5.700000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000
\n[ 5.730000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
\n[ 5.730000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
\n[ 5.740000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
\n[ 5.750000] usb usb1: Product: EHCI Host Controller
\n[ 5.750000] usb usb1: Manufacturer: Linux 3.14.42 ehci_hcd
\n[ 5.760000] usb usb1: SerialNumber: ehci-platform
\n[ 5.760000] hub 1-0:1.0: USB hub found
\n[ 5.770000] hub 1-0:1.0: 1 port detected
\n[ 5.770000] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
\n[ 5.780000] ohci-platform: OHCI generic platform driver
\n[ 5.810000] MT7628 USB Frequency Calibration start!
\n[ 5.810000] ohci-platform ohci-platform: Generic Platform OHCI controller
\n[ 5.820000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
\n[ 5.830000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000
\n[ 5.890000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
\n[ 5.900000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
\n[ 5.900000] usb usb2: Product: Generic Platform OHCI controller
\n[ 5.910000] usb usb2: Manufacturer: Linux 3.14.42 ohci_hcd
\n[ 5.920000] usb usb2: SerialNumber: ohci-platform
\n[ 5.920000] hub 2-0:1.0: USB hub found
\n[ 5.920000] hub 2-0:1.0: 1 port detected
\n[ 5.980000] mtk-sd: MediaTek MT76xx MSDC Driver
\n[ 5.990000] usbcore: registered new interface driver usb-storage
\n[ 6.110000] init: – preinit –
\n[ 6.560000] random: mktemp urandom read with 53 bits of entropy available
\nPress the [f] key and hit [enter] to enter failsafe mode
\nPress the [1], [2], [3] or [4] key and hit [enter] to select the debug level
\n[ 9.700000] mount_root: loading kmods from internal overlay
\n[ 10.100000] random: nonblocking pool is initialized
\n[ 10.130000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
\n[ 10.150000] procd: – early –
\n[ 10.150000] procd: – watchdog –
\n[ 10.930000] procd: – ubus –
\n[ 11.960000] procd: – init –
\nPlease press Enter to activate this console.
\n[ 13.060000] NET: Registered protocol family 10
\n[ 13.100000] gre: GRE over IPv4 demultiplexor driver
\n[ 13.110000] ip_gre: GRE over IPv4 tunneling driver
\n[ 13.120000] gpiodev: gpio device registered with major 251
\n[ 13.150000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
\n[ 13.170000] ip6_tables: (C) 2000-2006 Netfilter Core Team
\n[ 13.320000] Netfilter messages via NETLINK v0.30.
\n[ 13.330000] ip_set: protocol 6
\n[ 13.370000] u32 classifier
\n[ 13.370000] input device check on
\n[ 13.380000] Actions configured
\n[ 13.380000] Mirror\/redirect action on
\n[ 13.410000] PandoraBox IP Bandwidth load.
\n[ 13.840000] PandoraBox MT76x8 AP Driver Version-4.0.1.3(May 18 2015 15:34:34).
\n[ 13.860000] ip_tables: (C) 2000-2006 Netfilter Core Team
\n[ 13.950000] usbcore: registered new interface driver ums-alauda
\n[ 13.960000] usbcore: registered new interface driver ums-cypress
\n[ 13.970000] usbcore: registered new interface driver ums-datafab
\n[ 13.980000] usbcore: registered new interface driver ums-freecom
\n[ 13.990000] usbcore: registered new interface driver ums-isd200
\n[ 14.000000] usbcore: registered new interface driver ums-jumpshot
\n[ 14.010000] usbcore: registered new interface driver ums-karma
\n[ 14.020000] usbcore: registered new interface driver ums-sddr09
\n[ 14.030000] usbcore: registered new interface driver ums-sddr55
\n[ 14.040000] usbcore: registered new interface driver ums-usbat
\n[ 14.050000] usbcore: registered new interface driver usblp
\n[ 14.090000] xt_time: kernel timezone is -0000
\n[ 14.110000] PPP generic driver version 2.4.2
\n[ 14.120000] NET: Registered protocol family 24
\n[ 20.850000] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
\n[ 21.100000] PandoraBox MT76x8 AP Driver Version-4.0.1.3(May 18 2015 15:34:34).
\n[ 22.320000] Raeth v3.1 (Tasklet)
\n[ 22.320000]
\n[ 22.320000] phy_tx_ring = 0x02a8d000, tx_ring = 0xa2a8d000
\n[ 22.330000]
\n[ 22.330000] phy_rx_ring0 = 0x02854000, rx_ring0 = 0xa2854000
\n[ 22.350000] GMAC1_MAC_ADRH — : 0x0000000c
\n[ 22.360000] GMAC1_MAC_ADRL — : 0x432880bc
\n[ 22.360000] RT305x-ESW:Port0 Link Down
\n[ 22.380000] device eth0.1 entered promiscuous mode
\n[ 22.380000] device eth0 entered promiscuous mode
\n[ 22.410000] br-lan: port 1(eth0.1) entered forwarding state
\n[ 22.420000] br-lan: port 1(eth0.1) entered forwarding state
\n[ 23.960000] efuse_probe: efuse = 10000002
\n[ 23.960000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
\n[ 24.130000] tssi_1_target_pwr_g_band = 39
\n[ 24.420000] br-lan: port 1(eth0.1) entered forwarding state
\n[ 25.360000] RT305x-ESW:Port3 Link Up 100Mbps Full duplex
\n[ 29.890000] RT305x-ESW:Port3 Link Down
\n[ 30.260000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
\n[ 30.300000] jffs2_build_filesystem(): unlocking the mtd device… done.
\n[ 30.300000] jffs2_build_filesystem(): erasing all blocks after the end marker…
\n[ 33.070000] RT305x-ESW:Port3 Link Up 100Mbps Full duplex
\n[ 36.710000] done.
\n[ 36.710000] jffs2: notice: (1693) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.<\/p>\n

PandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login:
\nPandoraBox login: root
\nPassword:
\nLogin incorrect
\nPandoraBox login: admin
\nPassword:
\nLogin incorrect
\nPandoraBox login: root
\nPassword:
\nLogin incorrectPlease press Enter to activate this console.<\/p>\n

PandoraBox login:
\nLogin timed out Please press Enter to activate this console.<\/p>\n

PandoraBox login: root
\nPassword: <\/p>\n

BusyBox v1.22.1 (2015-05-09 15:44:33 CST) built-in shell (ash)
\nEnter ‘help’ for a list of built-in commands.<\/p>\n

_______________________________________________________________
\n | ____ _ ____ |
\n | | _ \\ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |
\n | | |_) \/ _` | ‘_ \\ \/ _` |\/ _ \\| ‘__\/ _` | _ \\ \/ _ \\ \\\/ \/ |
\n | | __\/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |
\n | |_| \\__,_|_| |_|\\__,_|\\___\/|_| \\__,_|____\/ \\___\/_\/\\_\\ |
\n | |
\n | PandoraBox SDK Platform |
\n | The Best solution for you |
\n | Copyright 2013-2015 D-Team Technology Co.,Ltd.SZ |
\n | http:\/\/www.pandorabox.org.cn |
\n |______________________________________________________________|
\n Base on OpenWrt BARRIER BREAKER (14.09, r858)
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#ifconfig
\nbr-lan Link encap:Ethernet HWaddr 00:0C:43:28:80:BC
\n inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
\n inet6 addr: fe80::20c:43ff:fe28:80bc\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:207 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:21152 (20.6 KiB) TX bytes:15173 (14.8 KiB)<\/p>\n

eth0 Link encap:Ethernet HWaddr 00:0C:43:28:80:BC
\n inet6 addr: fe80::20c:43ff:fe28:80bc\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:226 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:286 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:1000
\n RX bytes:26717 (26.0 KiB) TX bytes:67429 (65.8 KiB)
\n Interrupt:3 <\/p>\n

eth0.1 Link encap:Ethernet HWaddr 00:0C:43:28:80:BC
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:226 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:118 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:22649 (22.1 KiB) TX bytes:14027 (13.6 KiB)<\/p>\n

eth0.2 Link encap:Ethernet HWaddr 00:0C:43:28:80:BC
\n inet6 addr: fe80::20c:43ff:fe28:80bc\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:161 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:0 (0.0 B) TX bytes:51278 (50.0 KiB)<\/p>\n

lo Link encap:Local Loopback
\n inet addr:127.0.0.1 Mask:255.0.0.0
\n inet6 addr: ::1\/128 Scope:Host
\n UP LOOPBACK RUNNING MTU:65536 Metric:1
\n RX packets:2556 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:2556 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:0
\n RX bytes:154368 (150.7 KiB) TX bytes:154368 (150.7 KiB)<\/p>\n

ra0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
\n inet6 addr: fe80::200:ff:fe00:0\/64 Scope:Link
\n UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
\n RX packets:0 errors:0 dropped:0 overruns:0 frame:0
\n TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
\n collisions:0 txqueuelen:1000
\n RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
\n Interrupt:4 <\/p>\n

[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#iwconfig
\nifb0 no wireless extensions.<\/p>\n

ra2 MT76X8 APSoC ESSID:”HT_AP2″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:20:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

gre0 no wireless extensions.<\/p>\n

wds1 MT76X8 APSoC ESSID:”HT_AP1″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:10:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

eth0.1 no wireless extensions.<\/p>\n

lo no wireless extensions.<\/p>\n

ra1 MT76X8 APSoC ESSID:”HT_AP1″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:10:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

gretap0 no wireless extensions.<\/p>\n

teql0 no wireless extensions.<\/p>\n

wds0 MT76X8 APSoC ESSID:”PandoraBox_000000″
\n Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

ra0 MT76X8 APSoC ESSID:”PandoraBox_000000″
\n Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on
\n Link Quality=10\/100 Signal level:0 dBm Noise level:0 dBm
\n Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
\n Tx excessive retries:0 Invalid misc:0 Missed beacon:0<\/p>\n

apcli1 MT76X8 APSoC ESSID:””
\n Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on
\n Link Quality=10\/100 Signal level:0 dBm Noise level:0 dBm
\n Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
\n Tx excessive retries:0 Invalid misc:0 Missed beacon:0<\/p>\n

eth0 no wireless extensions.<\/p>\n

wds3 MT76X8 APSoC ESSID:”HT_AP3″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:30:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

ifb1 no wireless extensions.<\/p>\n

ra3 MT76X8 APSoC ESSID:”HT_AP3″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:30:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

apcli0 MT76X8 APSoC ESSID:””
\n Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on
\n Link Quality=10\/100 Signal level:0 dBm Noise level:0 dBm
\n Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
\n Tx excessive retries:0 Invalid misc:0 Missed beacon:0<\/p>\n

br-lan no wireless extensions.<\/p>\n

wds2 MT76X8 APSoC ESSID:”HT_AP2″
\n Mode:Managed Frequency=2.462 GHz Access Point: 02:00:00:20:00:00
\n Bit Rate:300 Mb\/s Tx-Power=18 dBm
\n Encryption key:off
\n Power Management:on<\/p>\n

eth0.2 no wireless extensions.<\/p>\n

[root@PandoraBox:\/root]#[ 742.600000] RT305x-ESW:Port3 Link Down<\/p>\n

[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]#
\n[root@PandoraBox:\/root]# <\/p>\n

OpenWRT\u652f\u63017628AN\u7684\u94fe\u63a5\uff1a<\/p>\n

https:\/\/openwrt.org\/toh\/views\/toh_dev_arch-target-cpu?dataflt%5B0%5D=cpu_%3DMediaTek%20MT7628AN<\/p>\n

#MediaTek MT7628AN, MediaTek MT7610EN
\nhttps:\/\/openwrt.org\/toh\/hwdata\/tp-link\/tp-link_tl-wr902ac_v3<\/p>\n

#MediaTek MT7628AN, MediaTek MT7612EN
\nhttps:\/\/openwrt.org\/toh\/hwdata\/hiwifi_gee\/hiwifi_gee_hc5861b<\/p>\n

#MediaTek MT7628AN, MediaTek MT7612E
\nhttps:\/\/openwrt.org\/toh\/hwdata\/wavlink\/wl-wn575a3 <\/p>\n

\u53c2\u8003\u8d44\u6599\uff1a<\/p>\n

https:\/\/blog.csdn.net\/gaoyang8320\/article\/details\/51126018
\nhttps:\/\/bbs.pcauto.com.cn\/topic-11780653.html
\nhttp:\/\/www.right.com.cn\/forum\/thread-154561-1-1.html<\/p>\n

http:\/\/www.right.com.cn\/forum\/thread-204532-1-1.html
\nhttp:\/\/www.right.com.cn\/forum\/thread-204532-1-1.html
\nhttp:\/\/www.right.com.cn\/forum\/thread-197663-1-1.html<\/p>\n

https:\/\/openwrt.org\/toh\/tp-link\/tp-link_archer_c20_v4
\nhttps:\/\/openwrt.org\/toh\/xiaomi\/nano?s[]=mt7628<\/p>\n","protected":false},"excerpt":{"rendered":"

OpenWRT\u6700\u65b0\u5de5\u7a0b\u76ee\u5f55\uff1ahttp:\/\/downloads.openwrt.org\/releases\/18. […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[4],"tags":[],"class_list":["post-2362","post","type-post","status-publish","format-standard","hentry","category-router"],"_links":{"self":[{"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/posts\/2362","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.51cos.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=2362"}],"version-history":[{"count":12,"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/posts\/2362\/revisions"}],"predecessor-version":[{"id":2375,"href":"http:\/\/www.51cos.com\/index.php?rest_route=\/wp\/v2\/posts\/2362\/revisions\/2375"}],"wp:attachment":[{"href":"http:\/\/www.51cos.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=2362"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.51cos.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=2362"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.51cos.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=2362"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}